I’ve received a bunch of feedback from Fujifilm photographers over the last few years about one specific thing, and I have never had a good answer to it. But just today I received a note from Fred Miranda with an excellent idea on how Fujifim could possibly fix the issue without too much trouble.
On some X-Trans IV and all X-Trans V cameras, the Custom Settings presets (often called C1-C7) save a lot more than IQ parameters. Focus settings, self timer settings, and even sound settings (and a whole lot more) must be programmed into the Custom Settings. The problem is that if you adjust some parameter because of the situation you are photographing in, the camera will forget this setting and restore whatever is saved into C1-C7 whenever the camera is powered off or goes to sleep.
One example is the focus mode on my Fujifilm X-E4. Since Fujifilm did not include an M/C/S switch, you have to set this within C1-C7. Since I mostly use autofocus lenses, this isn’t typically a problem, but whenever I use a manual focus lens, I need to set it to “M”. Whenever I power the camera Off and then On or change to a different C1-C7 Custom Settings preset, I have to set it back to “M” again. Otherwise, I must reprogram my Custom Settings to be “M” instead of “S” or “C”, and remember to change it back the next time I use an autofocus lens.
Another example is in situations with bright highlights (such as shooting into the sun), I prefer to use DR400 with the Reggie’s Portra Recipe, instead of DR-Auto, which will only choose DR100 or DR200. If I make this change and the camera goes to sleep, when I wake it up, it will be back at DR-Auto, unless I reprogrammed the Custom Settings preset with DR400 (which I’ll have to remember to change back).
There are probably a thousand different examples that I could give, and the specific ones that might annoy you the most might be different than what annoys me, but the larger point is that this is an annoyance for a lot of people. Some learn to “deal with it” (it is what it is) or sometimes they sell their X-Trans V model and return to their older camera. I think it is something that Fujifilm should address, and it might even be an easy fix.
The Custom Settings presets used to not behave this way—in fact, it doesn’t on my X-T30, X-T4 and X100V. C1-C7 used to be just for the IQ settings, which are the Film Simulation Recipe parameters. All the other settings—focus, sound, etc., etc.—were set within the menu. I think this worked well, except that “Base” was confusing (until you realize that it simply means the settings you are currently using). There are advantages and disadvantages to both concepts, so I don’t think simply going back to the old way is the answer. But the new process has some problems, for sure.
Fujifilm’s solution is Auto Update Custom Settings. If you Enable it, when you make a change, the camera will remember that change, and automatically adjust your C1-C7. However, one issue is that if you Enable Auto Update Custom Settings, your C1-C7 will most likely drift out of whack over time, and eventually not resemble what you programmed. This probably works for some, but it isn’t a good option for everyone. I always select Disable.
The proposed solution that Fred Miranda shared with me is a simple firmware update. In the Edit/Save Custom Settings menu, when you select (for example) C1, there are two empty lines: one above Edit/Check, and one below Edit Custom Name. Perhaps at the bottom Fujifilm could add Save IQ Settings Only, with the option to Enable or Disable. It could be default disabled (and, out of the box, the cameras would work the same as they do today), and enabled only if the user wants it to be enabled (what I would choose).
If you Enable Save IQ Settings Only, then all of the other options—AF/MF, Shooting Settings, Wrench, etc.—are greyed out when you program your C1-C7, as you won’t be able to set those within C1-C7. Whatever you have programmed into the Menu when no C1-C7 is selected (a.k.a. “None Selected” or, in the Q-Menu, “A/S/M/P”), is what those settings will be. Basically, it would make your C1-C7 function like it used to, and only be IQ (Recipe) settings.
What’s cool about this is that not only would it give you the choice, but it would give you the choice for each Custom Preset. You could Enable some, and Disable others. It gives you a lot more flexibility with how C1-C7 operates (make it work best for you). This seems like a fairly simple firmware update to create, so it shouldn’t require a lot of resources to implement. An easy fix, as they say, that should make everyone happy.
Now I don’t know if it would work with the PASM models, like the X-H2s, X-H2, X-S20, X-S10, or X-M5. The concept might need to be modified or completely nixed for those cameras, I’m not sure (I don’t own any, personally). But for the X-E4, X-T30 II, X-T5, X100VI, and X-T50, it should work like a charm. The X-T5, X-T50, and X100VI might be a good starting point. And it should definitely be implemented in future cameras—there’s plenty of time to bring this to whatever is in the pipeline.
I want to thank Fred for sharing this idea with me. I hope that Fujifilm reads this, and, if they do, takes it into consideration. This would improve the experience for many on the newer models, and I think it will prove itself worthwhile in the long run.